Asko Range F2 Error: Oven overheating trip
Asko range F2 error is a common issue reported by Asko appliance owners. What Does Asko Range Error Code F2 Mean? F2 means the thermal protection on the oven section has activated because the cavity temperature has exceeded safe limits. In a freestanding range this can occur due to thermostat failure, a runaway heating element, […]
No
DIY Fixable
From $150
Typical Repair Cost
45-90 min
Pro Repair Time
Quick Assessment
Answer to continue safely
Is it safe to keep using?
No. F2 indicates a potentially dangerous overheating condition. Do not use the oven section until the root cause is identified and repaired. The induction cooktop surface may still be functional.
Can I reset the code?
Yes. A breaker reset after full cooling clears F2. If the root cause is not fixed, F2 will return during the next cook cycle, potentially more quickly.
When to stop immediately?
Stop if you notice: Stop immediately and ventilate the kitchen if you see smoke coming from the oven cavity or vents., Do not resume oven use after F2 resets if the oven temperature overshoots by more than 30 °C in the low-temperature test..
Symptoms You May Notice
Oven shuts down at high temperature settings
During broiling or high-temperature roasting the oven suddenly cuts out with F2, leaving the cavity very hot and food undercooked.
F2 displayed with all oven heating stopped
F2 appears on the oven display and all elements de-energise; the oven cannot be restarted until it cools and is reset.
Range surround panels excessively hot
Side panels, the back panel, or the drawer compartment beneath the oven become unusually hot — indicating insufficient cooling airflow around the oven cavity.
Oven door seal visibly damaged or displaced
A torn or misaligned door gasket allows hot air to escape at high temperatures, contributing to the thermal overload and triggering F2.
Possible Causes
Thermostat runaway
A failed thermostat or NTC sensor sends a falsely low temperature reading, causing the control board to run the elements continuously and overshoot the set temperature.
Requires ProfessionalDamaged oven door seal
A worn or displaced door gasket allows hot air to escape, forcing the elements to work harder and longer, eventually tripping the thermal cut-out.
DIY PossibleCooling fan failure
The oven cooling fan that protects control electronics from heat has seized, causing the electronics bay to overheat and the secondary thermal protection to trip as F2.
Requires ProfessionalSafe Checks You Can Do
-
1
Allow full cool-down (60+ minutes)
After F2 trips, leave the range undisturbed with no cooking for at least 60–90 minutes. Keep children away from the hot oven exterior. Do not try to open the door repeatedly as this releases stored heat and prolongs cool-down.
A surface-contact thermometer placed on the side panel can confirm when the external surface has dropped to a safe temperature before you proceed.
-
2
Inspect the door seal
Once the oven is cool, open the door and run your fingers along the entire perimeter of the oven door gasket. Feel for tears, brittleness, gaps, or sections where the seal has fallen out of its retaining groove. A damaged seal needs replacement before further use.
Replacement door seals for Asko ranges are model-specific — reference the full model number from the rating plate on the door frame when ordering.
-
3
Test at low temperature after reset
After a breaker reset with the oven fully cooled, set the oven to 150 °C conventional bake only. Monitor with an independent oven thermometer for 25 minutes. If the oven exceeds 185 °C (35 °C above set) or F2 trips again quickly, a thermostat fault is confirmed — do not continue.
Document the maximum temperature reached for your service technician — this confirms whether the overshoot is minor (sensor drift) or severe (relay stuck on).
Tools required
When to Call a Professional
Contact a qualified technician if:
- F2 recurs within one or two cook cycles after a full cooling reset.
- Oven temperature overshoots the set temperature by more than 30 °C in the test at 150 °C.
- Oven exterior shows discolouration or heat damage consistent with repeated overheating events.
Need Professional Help?
Find qualified technicians in your area for proper diagnostics and repair.
Range Repair Service Schedule Appointment